FEATURED SOLUTION
LINETRAXX® NGRM700
Monitoring NGR resistance, neutral current and voltage in high-resistance-grounded systems.
Industries / Mining and metallurgy / Open-cast mining
Mining and metallurgy · BENDER DISTRIBUTOR IN TÜRKİYE
Insulation and Residual Current Monitoring in Open-Cast Mining
BENDER APPLICATION INTRODUCTION · BRIEF SUMMARY
Make mobile equipment supplies visible in open-cast mines
Connection monitoring for trailing-cable loads is distinct from general installation distribution monitoring. Bender’s mining brochure presents the RC48C approach and neutral grounding system components for these different application needs.
Bender distributor in Türkiye · ADEO Teknik
Sector brochure
Electrical safety in mining
Understand the application’s electrical needs.
Large excavators and conveyors may combine high- and low-voltage drives. Monitoring devices are selected with suitable coupling and measurement components according to voltage range and system arrangement.
Featured Bender products for this application
Start with models selected for the application’s measurement and monitoring duties; other products and accessories appear in the complete list below.
FEATURED SOLUTION
RC48C
Device jointly monitoring residual current and protective conductor continuity in cables with a pilot conductor.
Compare all related products ↓ · Product selection and quotations from the distributor ↗
Electrical monitoring from the neutral resistor to mobile equipment.
NGRM700 monitors the neutral grounding resistor in a high-resistance grounded (HRG) system. RC48C evaluates the protective conductor loop and residual current in a trailing cable with a pilot wire. These products focus on different measuring points in the distribution system and mobile load.
LINETRAXX® NGRM700
Monitors the neutral grounding resistor’s resistance, the fault current through it and the NGR voltage in an HRG system. Provides alarms and status information on resistor deterioration and earth faults.
- Evaluating NGR resistance through active and passive measuring methods
- Monitoring neutral current and voltage
- Providing operational information through configured relay outputs and communication
RC48C
Monitors protective conductor loop continuity in trailing cables with a pilot wire. Also evaluates residual current with a suitable measuring current transformer; open circuits, high resistance and short circuits are monitored according to the selected connection arrangement.
- Monitoring the PE and pilot-wire loop of mobile equipment
- Operation with a suitable termination unit and current transformer
- Signalling to a suitable switching chain through an alarm relay with two changeover contacts
Information flow on the system side
- Neutral and NGRResistance, current and voltage
- NGRM700Measurement and fault assessment
- Alarm / supervisory monitoringConfigured outputs and communication
Information flow on the mobile load side
- PE + pilot wireCable loop with compatible termination
- RC48C + suitable current transformerLoop and residual current evaluation
- Alarm / switching chainSelected contact and load switch arrangement
The diagrams show functional information flow. NGRM700 monitors the neutral grounding resistor; it is not a general-purpose earth electrode resistance tester. For RC48C, the pilot wire, termination unit, current transformer and switching arrangement are selected together according to the manufacturer’s connection diagram for the relevant variant.
Bender manufacturer sources: NGRM700 · RC48C · Mining brochure · PDF p. 5
FROM THE BENDER BROCHURE · APPLICATION GUIDE
Make mobile equipment supplies visible in open-cast mines
Connection monitoring for trailing-cable loads is distinct from general installation distribution monitoring. Bender’s mining brochure presents the RC48C approach and neutral grounding system components for these different application needs.
Related brochure section · PDF p. 5 ↗
Define trailing cable and protective connection requirements.
Earthing method, measuring current transformer and mechanical conditions are selected together in distribution and mobile equipment circuits.
Match NGR and earth fault monitoring duties to the distribution arrangement.
After choosing a product family for the application, compare the model’s measurement scope, accessory compatibility and communication options on its detail page.
Explore related Bender models ↓The explanation, Bender’s relevant sector publication and official application page form the basis of this content. The image is presented in its original form from the source brochure.
BENDER SECTOR PUBLICATIONS · ADEO TEKNİK
Bender sector brochures for this application.
BENDER SECTOR PUBLICATION
Electrical safety in mining
Official Bender manufacturer publication
Open brochure PDF ↗Download PDF ↓Bender source document ↗Other related Bender publications · 5 documents
BENDER SECTOR PUBLICATIONUS / North American edition
Electrical protection selection guide
Original publication: Electrical Protection Selection Guide
Bender manufacturer publication · US / North American edition
Open brochure PDF ↗Download PDF ↓Bender source document ↗
BENDER SECTOR PUBLICATIONUS / North American edition
Industrial applications · Bender solutions guide
Original publication: Bender Industry Applications
Bender manufacturer publication · US / North American edition
Open brochure PDF ↗Download PDF ↓Bender source document ↗
BENDER SECTOR PUBLICATION
Electrical safety in mines · application options
Original publication: Electrical Safety in Mines
Sector publication from Bender’s official download centre
Open brochure PDF ↗Download PDF ↓Bender source document ↗
BENDER SECTOR PUBLICATIONUS / North American edition
High- and low-resistance grounding · HRG/LRG
Original publication: High-Resistance and Low-Resistance Grounding Systems
Bender manufacturer publication · US / North American edition
Open brochure PDF ↗Download PDF ↓Bender source document ↗
BENDER SECTOR PUBLICATION
Earthing in electrical networks by region
Original publication: System Grounding in the Americas, Australia, South Africa and Other Regions
Sector publication from Bender’s official download centre
Open brochure PDF ↗Download PDF ↓Bender source document ↗BENDER SOLUTION GROUPS
From needs to product family.
Product families fulfil different measurement and notification duties. The model’s full scope and required components are identified in the relevant technical source.
BENDER PRODUCT FAMILYInsulation monitoring · IMD
Application-specific ISOMETER® insulation monitoring devices for IT systems.
Explore related products ↗
BENDER PRODUCT FAMILYResidual current monitoring
Single- and multichannel RCM / RCMS monitoring products for earthed circuits.
Explore related products ↗
BENDER PRODUCT FAMILYSystem components and accessories
Coupling devices, isolating transformers, power supplies and I/O components.
Explore related products ↗ADEO TEKNİK · BENDER DISTRIBUTOR IN TÜRKİYE
Let’s define the product
and its technical scope together.
You can request product information, manufacturer documentation and a supply quotation for this application.
Get product information for your application ↗- 01Application and systemApplication area, AC/DC configuration and nominal voltage.
- 02Product and technical documentationModel, variant, communication and compatible component information.
- 03Quotation and supplyDistributor support for product codes, quantities and accessory requests.
BENDER DISTRIBUTOR IN TÜRKİYE · PRODUCT SELECTION BY APPLICATION
Bender models for this application.
Earthing method, measuring current transformer and mechanical conditions are selected together in distribution and mobile equipment circuits.
Neutral grounding resistor monitoring · NGR
LINETRAXX® NGRM700
Monitoring NGR resistance, neutral current and voltage in high-resistance-grounded systems.
Measuring and monitoring relays
RC48C
Device jointly monitoring residual current and protective conductor continuity in cables with a pilot conductor.
Insulation monitoring · IMD
ISOMETER® iso685…
Insulation monitoring for inverter applications and large industrial installations.
Residual current monitoring
LINETRAXX® RCMS490-L
RCMS variant with LED indication and a separate alarm contact for each of its 12 measurement channels.
Measuring current transformers
LINETRAXX® CTUB100 series
AC/DC-sensitive measuring current transformer series comprising a CTBC core and electronic module.
Power quality and energy metering
LINETRAXX® PEM353
Voltage, current, power and energy measurement; THD and harmonic indicators up to the 31st order.
Insulation fault location
ISOSCAN® EDS30…
Portable insulation fault location in IT systems, with a separate residual current measurement function for TN/TT systems.
Communication and central monitoring
COMTRAXX® CP907-I
Condition monitor with a display and an integrated gateway.
Communication and central monitoring
POWERSCOUT®
Monitoring software combining electrical distribution data, events and long-term trends in web-based dashboards.
Residual current monitoring
LINETRAXX® RCMS460-D
Residual current monitor with 12 channels and a local graphic display, supporting multi-device monitoring via BMS.
Residual current monitoring
LINETRAXX® RCMS460-L
RCMS460 variant with channel alarm LEDs and BMS address indication for 12-channel systems.
Residual current monitoring
LINETRAXX® RCMS490-D
Monitoring device offering 12-channel residual current monitoring with the appropriate measuring current transformers.
System components and accessories
AGH150…
Coupling component extending the nominal voltage range of compatible ISOMETER® devices.
System components and accessories
AGH204S-4
Coupling device extending the voltage range of compatible ISOMETER devices in three-phase IT systems.
System components and accessories
AGH520S
Coupling device for connecting compatible ISOMETER models to AC systems up to 7.2 kV.
System components and accessories
AGH675S-7 / AGH675S-7MV15
Coupling devices for insulation monitoring in medium-voltage IT systems with IRDH275BM-7.
System components and accessories
AGH676S-4
Component extending the voltage range to 12 kV in AC IT systems with compatible ISOMETER devices.
OTHER OPTIONS IN THE PRODUCT FAMILY
Let’s select the variant for your needs.
Explore all options in the relevant family. Assess model selection alongside system topology, voltage, measurement requirements and accessory compatibility.
Neutral grounding resistor monitoring · NGRCompare 10 products / series in this family ↗
Measuring and monitoring relaysCompare 14 products / series in this family ↗Insulation monitoring · IMDCompare 30 products / series in this family ↗Residual current monitoringCompare 18 products / series in this family ↗
Measuring current transformersCompare 10 products / series in this family ↗Power quality and energy meteringCompare 2 products / series in this family ↗
Insulation fault locationCompare 5 products / series in this family ↗
Communication and central monitoringCompare 8 products / series in this family ↗
System components and accessoriesCompare 21 products / series in this family ↗Contact your distributor in Türkiye for Bender products.
As Bender’s distributor in Türkiye, ADEO Teknik provides technical product information and quotation support for model and accessory selection, manufacturer documentation and product supply.
BENDER TECHNICAL RESOURCES
Explore manufacturer documentation.
OFFICIAL MANUFACTURER SOURCE · EN
↗ISOMETER® / ISOSCAN® product portfolio
Manufacturer document · English
OFFICIAL MANUFACTURER SOURCE · EN
↗Residual current monitoring product portfolio
Manufacturer document · English
OFFICIAL MANUFACTURER SOURCE · EN
↗EDS309x D00012 N DEEN
Manufacturer document · English
Images and application content: official Bender sources. The relevant documents identify the exact model, variant and operating conditions.
EXPLORE THE SAME SECTOR
Other applications.
From application to product family
Explore product group introductions and original manufacturer brochures with ADEO Teknik, Bender’s distributor in Türkiye.
Insulation monitoring · IMDIn an IT system, live conductors are not directly connected to earth. Behaviour during the first insulation fault is assessed alongside the system configuration, leakage capacitances and protection arrangement.Read the product group guide ↗
Residual current monitoringDetecting sinusoidal AC, pulsating DC and smooth DC components requires different sensor and evaluator configurations. Choose A/F or B/B+ according to the application's current waveform.Read the product group guide ↗
System components and accessoriesIsolating transformers, coupling units, power supplies and auxiliary components perform different tasks. Select accessories alongside the main device's documents.Read the product group guide ↗Neutral grounding resistor monitoring · NGRNeutral grounding resistance and circuit topology determine the monitored quantities and device selection.Read the product group guide ↗
Measuring and monitoring relaysVoltage and frequency, current and protective conductor loop monitoring are different tasks. Relay selection starts with the quantity to be monitored.Read the product group guide ↗Measuring current transformersType A is considered for alternating and pulsating direct currents; suitable Type B sensors are assessed where smooth DC components must also be measured.Read the product group guide ↗
Power quality and energy meteringMain distribution, subdistribution and load levels are monitored according to the installation configuration. Multiple measuring points help assess the source of a change.Read the product group guide ↗
Insulation fault locationThe locating current injector, suitable measuring current transformers and EDS evaluator must be considered together.Read the product group guide ↗
Communication and central monitoringInterfaces such as BMS, BCOM and Modbus are selected according to the product's supported architecture. Do not assume every device supports every protocol.Read the product group guide ↗